Your question: How do you cut a roof in Revit?

Create an In-place family roof at choosing “Void extrusion”. Ideally in a section view draw the contourline of the void using the “Pick line” option on the base of the inside edge of the roof. Use the “Cut geometry” command and select first the roof than the void. After that you can click “Finish” to execute the cut.

How do you cut a ceiling in Revit?

Cut an Opening in a Floor, Roof, or Ceiling

  1. Click By Face or Vertical. Where is it? Architecture tab Opening panel. Structure tab Opening panel. …
  2. If you chose By Face, select a face in the floor, ceiling, or roof. If you chose Vertical, select the entire element. Selected face for opening by face. Selected element for vertical cut. …
  3. Click Finish Opening.

How do you split a roof in Revit?

Split a Roof or Structural Floor

  1. Select the floor to modify.
  2. Click Modify | Floors tab Shape Editing panel Add Split Line.
  3. Select a vertex, edge, face or point anywhere on the structural floor to start the split line. …
  4. Select another vertex, edge, face or point anywhere on the floor to end the split line.
IT IS INTERESTING:  You asked: How do you put a scope box on a sheet in Revit?

How do you cut in Revit?

Load the family into the project and place it. Click Modify tab Geometry panel Cut drop-down (Cut Geometry). Select the object to be cut. Select the instance with which to cut.

How do you use Cut command in Revit?

Click Modify tab Geometry panel Cut drop-down (Cut Geometry) and select the void you created. Notice the cursor changes shape. Select the geometry you created in Step 3. Revit Architecture cuts the selected geometry.

How do I make an opening in Revit?

Cut a Rectangular Opening in a Wall

  1. Open an elevation or section view where you can access the wall that will host the opening.
  2. Click (Wall Opening). Where is it? …
  3. Select the wall that will host the opening.
  4. Sketch a rectangular opening. …
  5. To modify an opening, click Modify, and select the opening.

21 янв. 2021 г.

How do you make a hole in the floor in Revit?

Cut an Opening in a Floor, Roof, or Ceiling

  1. Click By Face or Vertical. Where is it? Architecture tab Opening panel. Structure tab Opening panel. …
  2. If you chose By Face, select a face in the floor, ceiling, or roof. If you chose Vertical, select the entire element. Selected face for opening by face. Selected element for vertical cut. …
  3. Click Finish Opening.

How do you make a void family in Revit?

Create a Void Family with an Elliptic Profile

  1. Create a new family using the Metric Generic Model face based. …
  2. Select the 3D Front view.
  3. Click Create tab Datum panel (Reference Plane).
  4. Place a new horizontal reference plane in the middle of the slab extrusion:
  5. Select the new reference plane.
  6. In the Properties palette:
IT IS INTERESTING:  How do you rotate an object from vertical to horizontal in SketchUp?

17 нояб. 2020 г.

What is cut plane in Revit?

The cut plane is a plane that determines at what height certain elements in the view are shown cut. These 3 planes define the primary range of the view range. View depth is an additional plane outside of the primary range. You can set the level of view depth to show elements below the bottom clip plane.

How do you cut a void in Revit?

Open the Revit family with unattached voids and click Create tab Properties panel Family Category and Parameters. In the Family Category and Parameters dialog, select Cut With Voids when Loaded and click OK. Load the family into the project and place it. Click Modify tab Geometry panel Cut drop-down (Cut Geometry).

How do you cut a void wall in Revit?

Create an in-place family using the wall category, then draw the void shape. Use the Cut Geomety tool to pick the wall, then the void to cut it.

Sketch up